- Features
- Specification
- Applications
- Accessories
- Download
Feature
High luminance, internal graticule CRT
Japanese electronic encoder,light,handy and reliable
Fully sealed long live vertical mode switch
ALT Triggering Function. Two independent signals
simultaneous observation
30MHz Dual Channel
10 times sweep magnification
TV Synchronization-Y mode
Specification
Horizontal System
Sweep time: 0.2uSec~0.5Sec/DIV,20steps in 1-2-5 sequence;
Sweep time accuracy:±3%
Vernier sweep time control:≤1/2.5 of panel-indicated &#118alue;
Sweep magnification: 10 times;
×10MAG sweep time accuracy: ±5% (20nSec~50nSec are uncalibrated);
Linearity:±5%,×10MAG: ±10% (0.2s~1us)
Position shift caused by ×10MAG: within 2DIV. At CRT screen center
X-Y MODE:
Frequency bandwidth: DC to at least 500KHz;
X-Y phase difference:≤3°at DC~50KHz
Sensitivity: Same as vertical axis. (X-axis:CH1 input signal; Y-axis:CH2 input signal.);
CALIBRATION VOLTAGE
Waveform: Positive-going square wave;
Frequency: Approx. 1KHz;
Duty ratio: Within 48:52;
Output voltage: 2Vp-p±2%;
Output impedance: Approx.1KΩ
CALIBRATION SIGNAL
Waveform: Positive-going square wave;
Frequency: Approx. 1KHz;
Duty ratio: Within 48:52;
Output voltage: 2Vp-p±2%;
Output impedance: Approx.1KΩ
CRT
Type: 6-inch rectangular type, internal graticule;
Phosphor:P31;
Acceleration voltage: Approx.2KV(20MHz)/Approx.12kv(40MHz);
Effective screen size:8×10DIV[1DIV=10mm(0.39in)];
Graticule: Internal;
Trace rotation: Provided
VERTICAL AXIS
Sensitivity:5mV~5V/DIV,10 steps in 1-2-5sequence
Sensitivity accuracy:≤3%
Vernier vertical sensitivity: Continuously variable to 1/2.5 or less of panel-indicated &#118alue Frequency
bandwidth:
DC~30MHz(x5MAG:DC~7MHz)/DC~40MHz(x5MAG:DC~15MHz)DC~50MHz(X5MAG:DC~15MHz)
AC coupling: Low limit frequency 10Hz. (With reference to 100KHz, 8DIV, Frequency response with-3dB.)
Rise time: Approx.17.5ns (x5 MAG: Approx.50nS) Approx.8.75ns (x5 MAG: Approx.25nS)
Approx.7ns (x5 MAG: Approx.23.3nS)
Input impedance: Approx.1MΩ/Approx.25pF
DC balance shift: 5mV~5V/DIV: ±0.5DIV, 1mV~2mV/DIV ±2.0DIV
Linearity:<±0.1DIV of amplitude change when waveform of 2DIV at graticule center is moved vertically vertical modes: CH1 single channel; CH2 single channel; DUAL: CH1 and CH2 are displayed Simultaneously. ALT or CHOP selectable at any sweep at any sweep rate; ADD: CH1+CH2 algebraic addition Chopping repetition frequency: Approx. 250KHz Input coupling: AC, GND, DC Maximum input voltage: 300Vpeak (AC: frequency 1KHz or lower); common mode rejection ratio: 50:1 or better at 50KHz sinusoidal wave. (When sensitivities of Ch1 and Ch2 are set equally) Isolation between channels (At 5mV/DIV range): >1000:1 at 50KHz; >30:1 at 15MHz/>30:1 at 35MHz/>30:1 at 45MHz
CH2 INV BAL: Balanced point variation:≤1DIV (Reference at center graticule)
TRIGGERING
Triggering source: CH1,CH2,LINE,EXT
Coupling: AC: 20Hz to full bandwidth
SLOPE:+/-
Sensitivity: 20Hz~2MHz:1DIV, TRIG-ALT:2DIV EXT:200mV;TRIG-ALT:3DIV,EXT:800mV;
2~30MHz:1.5DIV;30MHz~40MHz:2.5DIV;40MHz~50MHz:3DIV;
TV: Sync pulse more than 1 DIV (EXT:1V)
Triggering modes: AUTO; NORM: TV-V: TV-H: (Both TV-V and TV-H synchronize only
when the synchronizing signal is negative)
EXT triggering signal input: Input impedance/: Approx:1MΩ/approx.25pF;
Max.input voltage:300V (DC+AC peak), AC: Frequency not higher than 1KHz